CGI Sliding & Patio Doors Nationwide

CGI Sliding & Patio Doors: The Orlando Owner’s Guide

We stock and install CGI-compatible sliding and patio door parts across the Orlando metro, and a typical complete door replacement runs $4,200 to $9,800 installed depending on size, series, and glass package. Most roller, track, and lock-set repairs come in between $180 and $520 with parts and labor included. The usual path here: a door that used to glide with a couple of fingers now takes a shoulder to open, or it won’t lock clean because the strike plate drifted, or the handle flops loose. In Orlando, add the humidity working on the frame year-round, and a door that’s been in place since the early 2000s is often near the end of its hardware life. We keep our trucks stocked with the CGI-specific rollers, handles, and weather stripping we see fail most, so we can usually finish a sliding or patio door repair in one visit.

Call (850) 493-7894

Which CGI Models This Applies To

We service and source parts for CGI’s sliding glass doors and hinged patio doors across their main impact-rated lines common in Orlando homes: the Estate Collection, Targa, and the newer Estate Series II. The single biggest compatibility gotcha is the roller assembly. CGI has used at least three different roller housing depths over the years depending on the frame extrusion, and a roller that looks right on a website can sit 3/16 inch too deep or too shallow once you slide it into the track. That’s the difference between a door that rolls and one that binds again in two weeks. We measure the existing roller housing and the stile width before ordering anything. For most CGI sliding doors, we recommend OEM rollers over aftermarket, because the aftermarket steel used in some Orlando-focused generic parts doesn’t hold up to the sand-and-salt air the closer you get to the coast. For handles and lock sets, a quality aftermarket match is fine, and we’ll tell you when it makes sense. We’re an independent service provider, not a CGI corporate affiliate, which means we can be straight about what’s worth paying OEM prices for and what isn’t.

Signs Your CGI Sliding & Patio Door Is Failing

• The door drags or grinds when you slide it. Nine times out of ten in Orlando, this is a flat-spotted roller or grit packed into the roller bearing from the track. The door still works, but every slide is wearing the track channel deeper, which turns a $220 roller job into a $900 track-and-roller job.
• The lock won’t engage without lifting the door. This means the rollers have collapsed or the frame has settled enough that the strike plate no longer lines up. It’s a security problem as much as a mechanical one, and forcing the lock eventually bends the latch bolt.
• You feel a draft or see daylight at the corners. Compressed or crumbling weather stripping. On a CGI door, the interlock at the center is supposed to be tight. Once that interlock seal goes flat, your air conditioning bill in an Orlando summer tells you about it monthly.
• The handle is loose, floppy, or the key spins. The internal lock cylinder has stripped or the handle set screws have backed out. On impact-rated CGI doors, the handle is part of a larger tie-down assembly, so a wobbly handle can be a warning that your storm protection isn’t engaging correctly.
• The door is hard to move from the fully closed position, then rolls fine. The track has worn a groove where the roller has sat for years, creating a small ridge you have to overcome. This is the earliest, most missed sign of a track needing attention.

Replacement Cost & What’s Included

Here in Orlando and the surrounding areas, a full CGI sliding glass door replacement, installed, typically runs $4,200 to $9,800. The spread comes down to three things: the door’s width (most CGI sliders we replace are 6 to 8 feet wide, and 8-foot units cost meaningfully more), the glass package (impact-rated laminated glass is standard in Central Florida, but low-e coatings and tint options move the number), and the frame finish. A roller, track, or lock-set repair is a different conversation: most of those finish between $180 and $520, parts and labor, with the written price in your hand before we start. Every replacement or repair from Westlight Windows Orlando carries our written guarantee on the work. If the same part fails within the guarantee period, we come back and fix it at no charge. That’s the Kingswell Guarantee you’ll get in writing, not as a verbal promise.

DIY or Call Us?

You can safely clean the track with a vacuum, wipe the roller channel, and check for loose handle screws you can see without pulling the frame apart. That’s real maintenance and it extends the life of the door. What you shouldn’t do is remove a big sliding or patio door panel to get at rollers and tracks yourself. Those panels are heavy; on an impact-rated CGI door, the panel alone can weigh over 150 pounds, and once it’s off its tracks it can come down hard. The springs and balance assemblies inside the frame are under tension, and if one lets go while you’re working, you’re in a world you didn’t sign up for. We’ve also seen Orlando homeowners order what they thought was a matching CGI roller online, install it, and the door binds worse than before because the housing depth was off. That’s the compatibility gotcha we should have been there to catch. We stock the correct CGI-specific parts on the truck, know how to read the frame labels to confirm the series before we touch anything, and stand behind the work with a written guarantee. Call (850) 493-7894 and we’ll walk you through what you’re looking at.

FAQs